Danby Appliance Repair Montreal
Specialized in-home Repair and Installation of Danby compact & full-size appliances for condos, apartments, and homes.
Specialized in-home Repair and Installation of Danby compact & full-size appliances for condos, apartments, and homes.
Our technicians are trained to focus on certain brands to improve efficiency
Give us a call, we will send a professional repairman to your home that specializes on your brand.
Danby Residential or Commercial appliances.
Flash Repair
We service Danby compact refrigerators, chest & upright freezers, 18–24" dishwashers (built-in & portable), 20–24" ranges, and compact washers/dryers. Technicians carry common parts and provide clear, upfront pricing.
| Fault/Code | Condition/Description | Solution |
|---|---|---|
| E1 | Fill timeout / low pressure | Open valve; clean inlet screen; test inlet valve; verify pressure. |
| E2 | Drain error | Clear filter, air gap and hose; test drain pump/impeller. |
| E3 | Heating fault / low temp rise | Test heater & NTC; inspect relay/control. |
| E4 | Overflow/leak detected | Dry base; check float/micro-switch; repair leak source. |
| E5 | Circulation pump error | Check pump windings/obstruction; replace circulation motor if failed. |
| E6 | Temp sensor fault | Ohm thermistor; repair harness; replace sensor/control. |
| E7 | Turbidity/OWI error (if equipped) | Clean sensor; check wiring; replace OWI. |
| U1 | Door not latched | Adjust latch/strike; replace latch switch if open. |
| U3 | Key stuck / UI fault | Reseat ribbon; replace console/UI. |
| PF | Power failure | Clear; verify supply/breaker/neutral. |
| Fault/Code | Condition/Description | Solution |
|---|---|---|
| F1 | Control fault / stuck key | Power reset; replace EOC or keypad if recurring. |
| F2 | Runaway temperature | Test temp sensor/RTD and relays; replace failed component. |
| F3 | Sensor open | Measure RTD ~1080Ω @ 70°F; repair harness or replace. |
| F4 | Sensor short | Inspect shorts; replace RTD/control as required. |
| F5 | Latch/door lock error (if self-clean) | Test latch motor/switches; replace assembly. |
| Ign | Gas ignition failure | Check igniter draw (≥3.2A typical); replace igniter/valve. |
| Fan | Cooling fan not running (if equipped) | Test fan motor & tacho; replace fan. |
| PF | Power failure | Clear; verify supply/breaker/terminal block. |
| L2 | Low line voltage (electric) | Check supply wiring/outlet; involve electrician if needed. |
| Key | Key stuck / UI fault | Reseat ribbon; replace UI/clock. |
| Fault/Code | Condition/Description | Solution |
|---|---|---|
| HI | High temperature alarm | Clean condenser; verify fans; check gasket; test sealed system. |
| d | Door open | Adjust hinges; test door switch; replace gasket if leaking. |
| E1/E2 | Sensor faults | Ohm NTCs; repair wiring; replace sensor/control. |
| DF | Defrost error | Test heater/bi-metal/ADC; replace failed part. |
| CF | Compressor/inverter fault (select) | Test start device/inverter; evaluate compressor. |
| FAN | Evap/condenser fan error | Test voltage & rotation; replace motor. |
| ICE | Icemaker fault (if equipped) | Run IM test; replace module, motor or valve. |
| rS | Sealed system underperforming | Leak/charge diagnostics by certified tech. |
| Filter | Filter change reminder | Replace filter; reset indicator. |
| PF | Power failure | Clear alarm; verify supply/surge protection. |
| Fault/Code | Condition/Description | Solution |
|---|---|---|
| E1 | Lid open / lock fault | Adjust strike; replace lid lock/switch. |
| E2 | Fill fault / low pressure | Open valves; clean screens; test inlet valve. |
| E3 | Drain timeout | Clear pump & hoses; replace drain pump if weak. |
| E4 | Unbalance | Redistribute load; level feet; check suspension. |
| E5 | Motor fault | Inspect capacitor/motor; replace failed components. |
| E6 | Thermistor/NTC fault (select) | Ohm sensor; replace if out of range. |
| E7 | Door not closed (front models) | Replace door lock assembly. |
| dE | Door error | Check latch & wiring; replace lock. |
| LE | Drive overload | Check basket/belt; motor windings; control. |
| PF | Power failure | Clear; verify outlet/breaker. |
| Fault/Code | Condition/Description | Solution |
|---|---|---|
| E1 | Overheat / hi-limit trip | Clean lint & ducts; test thermostats/NTC. |
| E2 | Heater open | Check element continuity and relays; replace if failed. |
| E3 | Motor fault | Test motor/capacitor; replace if defective. |
| E4 | Moisture sensor fault | Clean bars; check harness; replace sensor PCB. |
| E5 | Thermistor out of range | Ohm NTC; replace sensor or control. |
| E6 | Door switch fault | Replace door switch if open/shorted. |
| E7 | Control relay error | Inspect board; replace main PCB. |
| AF | Restricted airflow | Clean exhaust path; check blower wheel. |
| L2 | Low line voltage | Verify supply/breaker/receptacle. |
| PF | Power failure | Clear and retest; confirm dedicated circuit. |
Monday to Friday
7:00am - 9:00pm
Saturday
10:00am - 5:00pm
Sunday
12:00am - 5:00pm